Unplug the machine and wait for it to cool. If the indicator light will not turn off, there may not be enough water in the machine. On average, the Bissell SteamShot takes about 30 seconds to 2 minutes to heat up and produce steam. Before using the steamer, it is important to wait for the indicator light to shut off. Once the machine has finished heating the water, the light will turn off. The Bissell SteamShot indicator light will light up (orange) when the machine is building up pressure and heating the water. Bissell SteamShot indicator light problemsįill the Bissell SteamShot with water and plug the machine into a working outlet. The safety cap must be pushed down and turned counter clockwise in order to be removed. Once cooled, the cap should become unstuck and come off. Unplug the machine and allow it to cool before opening the cap.īefore opening the Bissell SteamShot water tank cap, relieve pressure inside the machine by holding the steam trigger. The Bissell SteamShot water tank cap will not come off the machine if the steam temperature inside the tank is too hot. If you feel like the machine is continually spraying steam from the safety cap, or is spraying a large amount of steam, contact Bissell Customer Support. However, it is important to not hold the machine near the cap area. This is how the machine vents to prevent too much pressure building up. Steam coming from the cap area is normal. If there is steam coming out of the Bissell SteamShot safety cap, there is nothing to worry about. Either steam is coming out of the safety cap, or the safety cap will not come off, even after spinning it counter clockwise. There are two common issues with the Bissell SteamShot safety cap. While it may seem okay to put the unit under the tap and fill it up, it's best to use the measuring cup to hit the max fill of 360ml or 6.6oz as the jug is labelled. Try spraying the machine while holding it level.Īdditionally, the water can dribble from the Bissell SteamShot's top-valve as it is heating up and the nozzle can shoot hot water rather than steam for the first minute or so if you overfill the water tank.Īlways use the measuring cup to fill the Bissell SteamShot. If the Bissell SteamShot is tilted too far (and this varies based on how much water is in the tank), the machine can dribble or spray water from the nozzle. Do not tilt the steamer more than 45° during use as boiling water could spill with the steam. The Bissell SteamShot is designed to not be held at more than a 45-degree angle. Always use the measuring cup to fill the water tank. There are two possible reasons why a Bissell SteamShot is spraying hot water: Then clean and unclog the nozzle using the end of a paperclip. If the Bissell SteamShot does not spray without the tool, wait at least 5 minutes for the machine to cool down. If the machine produces steam without the tool attached, clean and unclog the spray tip on the tool with a paperclip. Take the tool off from the Bissell SteamShot and see if it sprays without the tool connected. Here’s how to check and unclog the Bissell SteamShot if the nozzle is clogged: If the Bissell SteamShot has successfully heated up the water (the indicator light will turn off when it’s ready), but there is no steam when you press the trigger, the steam nozzle may be blocked. If the indicator turns off but there is no steam, the steam nozzle may be blocked Always unplug the steamer before filling/refilling. Not only will it cause damage to the heating element, but it will also void your warranty. You can buy a new unit or contact Bissell if you are still under warranty. If the indicator turns on but won’t turn off (the water is not getting hot), there is a problem with the heating element. This indicates that the Bissell SteamShot is ready for use. The indicator light will turn on.Īfter about 30 seconds to 2 minutes, the indicator light should turn off. Try using a different outlet if the first one does not work. Once the machine has been filled with water, plug the Bissell SteamShot into a functioning outlet. If the indicator turns on but won’t turn off, there is a problem with the heating element (water not getting hot) If the cord is damaged, get it fixed or buy a new machine. Unplug the machine and run your hand along the cord while looking for damage or exposed wires. If the indicator light fails to turn on, there is a problem with the cordĬheck the cord. Lastly, if the indicator turns off but there is no steam, the steam nozzle may be blocked. If the indicator turns on but won’t turn off, there is a problem with the heating element. If the indicator light fails to turn on, there is a problem with the cord. There are three reasons why a Bissell SteamShot is not steaming.
0 Comments
Leave a Reply. |